Modicon Power Supply
Schneider Electric replaces Phaseo ABL power supplies with new range of Modicon ABL power supplies.
The Modicon ABL switch mode power supply offer is designed to provide the DC voltage necessary for the automation system equipment control circuits. Modicon industrial power supplies are regulated switch mode power supplies, available in 3 types: ABLM Modular, ABLS Optimized, and ABL8RP/WP Universal.
They are fully electronic with a regulated output voltage. The use of electronics makes it possible to significantly improve the performance of these power supplies, which offer:
- Compact dimensions
- Integrated overload, short-circuit, overvoltage, and undervoltage protection
- Wide input voltage range
- High degree of output voltage stability
- Efficiency - Diagnostics via LEDs on the front panel
- Remote diagnostics via relay contact with ABL8RP/WP Universal
They deliver a stabilized DC output voltage that is precise to less than 3%, whatever the load from an AC line supply, within the following ranges:
- 100 to 240 Vac for phase-to-neutral (N-L1) or phase-to-phase (L1- L2) connections for the ABLM Modular, ABLS Optimized and ABL8RPM universal types
- 100 to 500 Vac for phase-to-neutral (N-L1) or phase-to-phase (L1- L2) connections for the ABL8RPS Universal types
- 380 to 500 Vac for 3-phase connections (L1-L2-L3) for the ABL8WP Universal types
- They comply with IEC standards and are certified to comply with the major certifications bureau standards (1). Power supplies with 24 Vdc output and power output equal or lower than 90 W are also NEC Class 2 and Limited Power Source compliant (Except ABL8RPS24030)
- The harmonic pollution is reduced to a minimum level across the entire Modicon power supply types, ensuring compliance with the requirements of standard IEC/EN 61000-3-2
Modicon power supplies incorporate:
- An output voltage adjustment potentiometer to help compensate for any line voltage drops in installations with long cable runs (3)
- Direct mounting on 35 mm (1.37 in) omega rail
Protective extra low voltage (PELV) and Safety extra low voltage (SELV)
The Modicon power supplies can be used to supply protection extra low voltage (PELV) or safety extra low voltage (SELV) control circuits in compliance with standard IEC/EN 60364-4-41.
They have the following characteristics:
- Double insulated between the input circuit (connected to the line supply) and the low voltage output circuit via an integrated isolation transformer
- Internal circuitry limiting the output voltage to less than 60 V under single fault conditions
Harmonic pollution (power factor)
The current drawn by a power supply is not sinusoidal. This leads to the generation of harmonic currents that pollute the distribution network. European standard IEC/EN 61000-3-2 limits the harmonic currents produced by power supplies. This standard covers devices between 75 and 1000 W, drawing up to 16 A per phase, and connected directly to the public distribution network. Modicon ABL8RP/WP Universal and ABLS Optimized from 75 W power supplies conform to IEC/EN 61000-3-2 and can therefore be connected directly to public distribution networks. Since ABLM Modular, ABLS1A12062,ABLS1A24021, and ABLS1A24031 power supplies have power ratings that are less than 75 W, they are not subject to the requirements of standard IEC/EN 61000-3-2. They can therefore be connected directly to public distribution networks.
Modicon ABLM Modular-serie power supply
The ABLM Modula-serie meets the needs of simple automation systems with power ratings from 10 to 60 W and an output voltage of 5, 12 or 24 Vdc.
- The shape and compact nature of the housing mean that it can be mounted directly on a panel, in a modular distribution panel or on a omega rail in a cabinet
- Modicon ABLM Modular power supply conform to the Overvoltage Category III and therefore can be directly connected to central distribution boards. In the event of an overload the power supply protection interrupts power; when the source of the overload has been corrected, the power supply reverts to its nominal state (automatic reset)
Presentation:
The Modicon ABLM Modular are regulated power supplies designed to supply control circuits in industrial and building automation up to 60 W.
- Thanks to their modular housing, they can be installed either in enclosures (Spacial and Thalassa) or industrial panels by clipping on omega (DIN) rail
- Direct, fixed mounting on panel is also possible without additional parts thanks to the integrated mounting lugs
- Available with 18, 36 and 53 mm (0.70, 1.41, and 2.09 in) widths, ABLM modular power supplies are one of the most compact ranges on the market
- Modicon ABLM Modular power supply meet NEC Class 2 and LPS (Limited Power Source) requirements
- Modicon ABLM Modular power supply conform to the Overvoltage Category III and therefore can be directly connected to central distribution boards
- A ‘QR’- code is printed on the front of the power supplies and gives a direct access to the latest technical documentation
- Modicon ABLM Modular power supplies are the right choice for use with Zelio logic Smart relays.
Main Features
| Nominal input voltage | 100…240 Vac |
| Network system compatibility | TN, TT, IT |
| Nominal output voltage | 5, 12 and 24 Vdc |
| Operating temperature | -25°C…+70°C (-13 … 158°F) |
| Operating altitudes | 0...2000 m ((6561.6 ft) 0…5000 m (16404.2 ft) with Derating |
| Product certifications | CE marking - CB Scheme - cULus Listed - cURus Recognized - RCM - EAC |
| Conformity to standards | IEC/EN 62368-1 - IEC/EN 61010-1 - UL/CSA 61010-1 - UL/CSA 61010-2-201 |
Modicon ABLS Optimized-serie power supply
The ABLS Optimized-serie offers competitive functionality for applications supplied with 12, 24 or 48 Vdc and with power ratings from 50 W up to 480 W.
Presentation:
The Modicon ABLS Optimized are regulated power supplies, designed to supply control circuits in industrial applications from 50 up to 480 W.
They are available in 2 housing formats for a better adaptation to the enclosure:
- compact housing 75 mm height (2.95 in)
- book housing 124 mm height (4.88 in)
- Available with a width from 27 mm (1.06 in), ABLS optimized power supplies are one of the slimmer ranges on the market
- The printed circuit board of the power supplies (book housing) has a conformal coating in order to resist to common dust and chemical pollutants
- Modicon ABLS Optimized power supply meet NEC Class 2 and LPS (Limited Power Source) requirements
- Up to 6 output terminals make wiring easier
- A ‘QR’- code is printed on the front of power supply and gives a direct access to the latest technical documentation
- Modicon ABLS Optimized power supplies are the right choice for use with Modicon M221/M241/M251 logic controllers and Modicon M262 logic/motion controllers.
Main Features
| Nominal input voltage | 100…240 Vac, 140…340 Vdc |
| Network system compatibility | TN, TT, IT |
| Nominal output voltage | 12 , 24 and 48 Vdc |
| Operating temperature | -20…+70°C (-4…+158°F) |
| Product certifications | - CE marking - CB Scheme - cULus Listed - cURus Recognized - RCM - EAC |
| Conformity to standards | - IEC/EN 62368-1 - IEC/EN 61010-1, IEC/EN 61010-2-201 - UL/CSA 61010-1, UL/CSA 61010-2-201 - UL 508/CSA C22.2 No. 107.1 |
Detail information and specifications to be found in this catalog.
Stay up to date with the latest news:
-
Rittal - VR pedestalRead moreDelve into the world of the VX plinth plinth system - a successor that takes your cabinet arrangement to the next level. More stability, but also flawless installation. Experience the evolution of your workspace today! Rittal strives to constantly refine and improve its products. As part of this process, the VX plinth plinth system has been redesigned this product has been available since 1 March 2024.
-
Siemens - SINAMICS G220 variable speed drive now also in IP55Read moreIn addition to the previously released IP20 variant of the SINAMICS G220 variable speed drive, the IP55 version of this innovative drive is now also available. This version comes standard with coated circuit boards that make the inverter resistant even outside the control cabinet to aggressive influences in a harsh industrial environment. As an option, a housing-mounted isolating switch can also be supplied to ensure safe disconnection of voltage without any other external components.
-
News - Fluke - 87-V digital multimeterRead moreTechnological advances now allow accurate electrical measurements to be taken during installation and maintenance using a digital multimeter (DMM), allowing technicians to diagnose problems that lead to premature failure.
-
Pilz: PSENmlock mini and PSENslock 2Read moreWhen securing fences, a wide variety of factors such as the fence type, the respective installation situation and the specific use must be taken into account depending on the application. For this purpose, Pilz is expanding its range in the field of safety interlocks with two new sensors immediately: PSENmlock mini for space-critical applications and PSENslock 2
Check out our other success stories:
-
Dymotec - Open Lines in a ‘Perfect Storm’Read moreCOVID-19 and global component scarcity threw the industry into a ‘perfect storm’. Industrial automator Dymotec and Breemes kept the phone lines constantly open to tackle the scarcity problem together with creativity and proactivity. Dymotec in Olen (B) focuses on industrial automation spanning a broad spectrum of industries, from food and pharma to logistics and metal. The company has been around for 30 years and joined the Jeco Energies Group in 2022. Dymotec now has some 50 employees and also has a flexible shell with technicians, programmers and project engineers. Ever since its establishment, the company from Kempen has had a relationship with (the predecessors of) Breemes.
-
Enduro - Complete package for heavy-duty workRead moreEnduro Softslings builds machines for the manufacture of its own heavy lifting soft slings. For a new machine, it called in itsme for the full package: advice on the drives, supply of components and programming of the controls. “We completed the entire project in just over six months. That’s fast for such a specialised machine.”
-
Stimac - Good technical support for ever-changing specificationsRead moreIf the description for an automation project is clear from the start, it is easy for the industrial automation specialist to give it substance. In practice, however, specifications often change during the course of a project. This happened to Stimac/SNK when designing the control technology for a horticultural machine. For the problems that arose during the process, itsme quickly provided Stimac/SNK with a solution. “When a customer calls us, we respond immediately. So it’s nice to have a supplier like itsme who can also help immediately.”
-
Innovatec - Hatching Better ProcurementRead moreInnovatec Hatchery Automation launched a process of professionalisation for its procurement process last year. The company partnered with itsme because of its technical expertise, logistics concepts and intensive contacts with manufacturers. “First we were dating, but now we’re thinking about moving in together.”
Why not take a look at these trainings we offer:
-
TIAP-NETWORKRead moreavailable in Dutch
-
PCS7-SYST v9Read moreavailable in Dutch
-
PCS7-PRO v9Read moreavailable in Dutch
-
PROFIBUS-INSTRead moreavailable in Dutch